泥浆泵、压裂泵及配件 一站式全球供应制造商
创新技术 卓越品质
0532-58628118
学习 创新 超越
泥浆泵、压裂泵及配件 一站式全球供应制造商
创新技术 卓越品质
0532-58628118
企业名称：青岛海诺奥石油机械制造有限公司
联系人：王总
固话：0532-58628118
电话：15153273539
邮箱：hna@pumpparts.cn
网址 : www.pumpparts.cn
地址：崂山区文岭路5号白金广场C座701
序号 | HNA 部件号 | 名称 | 数量 |
0 | HNA 400HT-4.5-0 | 液力端总成 | 1 |
1 | HNA 400 HT -4.5-1 | 阀箱 | 1 |
2 | HNA 400 HT -4.5-2 | 阀座O型圈 | 6 |
3 | HNA 400 HT -4.5-3 | 阀座 | 6 |
4 | HNA 400 HT -4.5-4 | 阀胶皮 | 6 |
5 | HNA 400 HT -4.5-5 | 阀体 | 6 |
6 | HAN 400 HT -4-6 | 弹簧 | 6 |
7 | HNA 400 HT -4-7 | 排出压盖 | 3 |
8 | HNA 400 HT -YM-5.75 | 排出（吸入）压帽 | 6 |
9 | HNA 400 HT -4-9 | 压盖密封II | 6 |
10 | HNA 400 HT -4-10 | 压盖密封II钢圈 | 6 |
11 | HNA 400 HT -4.5-11 | 柱塞端垫圈 | 3 |
12 | HNA YL-HXMF-4.5 | 弧型密封 | 3 |
13 | HNA YL-VXMF-4.5 | V型密封 | 3 |
14 | HNA 400 HT -4.5-14 | 柱塞油环 | 3 |
15 | HNA 400 HT -4.5-15 | 油环O型圈 | 3 |
16 | HNA 400 HT -4.5-16 | 油环油封 | 3 |
17 | HNA 400 HT -4.5-17 | 盘根盒压帽 | 3 |
18 | HNA 400 HT -4-18 | 盘根盒支承座 | 3 |
19 | HNA 400 HT -4-20 | 盘根盒销钉 | 3 |
20 | HNA 400 HT -4.5-20 | 柱塞 | 3 |
21 | HNA 400 HT -4-22 | 柱塞拉杆 | 3 |
22 | HNA 400 HT -4.5-22 | 柱塞堵头衬垫 | 3 |
23 | HNA 400 HT -4.5-23 | 柱塞堵头 | 3 |
24 | HNA 400 HT -4.5-24 | 阀体导向座 | 6 |
25 | HNA 400 HT -4-26 | 护套 | 12 |
26 | HNA 400 HT -4.5-26 | 弹簧座 | 3 |
27 | HNA 400 HT -4.5-27 | 压簧 | 3 |
28 | HNA 400 HT -4-28 | 弹簧座护套 | 6 |
29 | HNA 400 HT -4.5-29 | 吸入压盖 | 3 |
30 | HNA 400 HT -4.5-30 | 泵拉杆 | 1 |
31 | HNA 400 HT -4.5-31 | 泵拉杆垫片 | 2 |
32 | HNA 400 HT -4.5-32 | 泵拉杆螺母 | 2 |
33 | HNA 400 HT -4.5-33 | 排出法兰（双油壬） | 1 |
34 | HNA 400 HT -4.5-34 | 3” 油壬密封 | 1 |
35 | HNA 400 HT -4.5-35 | 法兰螺母 | 4 |
36 | HNA 400 HT -4.5-36 | 法兰螺栓弹簧垫 | 4 |
37 | HNA 400 HT -4.5-37 | 法兰螺栓 | 4 |
38 | HNA 400 HT -4-34 | 排出法兰密封 | 6 |
39 | HNA 400 HT -4-35 | 排除法兰衬套 | 2 |
40 | HNA 400 HT -4-37 | 盲法兰 | 1 |
41 | HNA 400 HT -4.5-41 | 下连接杆螺母 | 2 |
42 | HNA 400 HT -4-42 | 下连接杆螺母垫片 | 2 |
43 | HNA 400 HT -4.5-43 | 下连接杆 | 1 |
44 | HNA YL-YRMF-2 | 2” 油壬密封 | 1 |
HNA 600S-TWS 柱塞泵液力端配件清单
序号 | HNA 部件号 | 名称 | 数量 |
0 | HNA 600-3-0 | 液力端总成 | 1 |
1 | HNA 1000S-3”-005 | 阀箱 | 1 |
2 | HNA 1000S-3”-2 | 阀座O型圈 | 6 |
3 | HNA 1000S-3”-3 | 阀座 | 6 |
4 | HNA 1000S-3”-4 | 阀胶皮 | 6 |
5 | HNA 1000S-3”-5 | 阀体 | 6 |
6 | HNA 1000S-3”-6 | 弹簧 | 6 |
7 | HNA 1000S-3”-7 | 压盖密封 | 6 |
8 | HNA 1000S-3”-8 | 排出压盖 | 2 |
9 | HNA 1000S-3”-9 | 排出（吸入）压帽 | 5 |
10 | HNA 600-3-10 | 盘根座圈 | 3 |
11 | HNA 600-3-11 | 盘根座O型圈I | 3 |
12 | HNA 600-3-12 | O型圈I挡圈 | 3 |
13 | HNA 600-3-13 | O型圈II挡圈 | 3 |
14 | HNA 600-3-14 | 盘根座O型圈II | 3 |
15 | HNA 600-3-15 | 弧型密封 | 3 |
16 | HNA 600-3-16 | V型密封 | 3 |
17 | HNA 600-3-17 | 衬环 | 3 |
18 | HNA 600-3-18 | 油环 | 3 |
19 | HNA 600-3-19 | 柱塞 | 3 |
20 | HNA 600-3-20 | 柱塞压帽油封 | 3 |
21 | HNA 600-3-21 | 柱塞压帽 | 3 |
22 | HNA 1000S-3”-22 | 下弹簧座 | 3 |
23 | HNA 1000S-3”-23 | 吸入压盖 | 3 |
24 | HNA 600S-3”-24 | 排出法兰 | 1 |
25 | HNA 600S-3”-25 | 排出法兰O型圈 | 2 |
26 | HNA 1000S-3”-26 | 2”油壬密封 | 1 |
27 | HNA 1000S-3”-27 | 排出法兰螺母 | 8 |
28 | HNA 1000S-3”-28 | 平垫圈 | 8 |
29 | HNA 1000S-3”-29 | 双头螺栓 | 8 |
30 | HNA 600S-3”-30 | 盲法兰 | 1 |
31 | HNA 600S-3”-31 | 排出法兰端面O型圈 | 2 |
32 | HNA 1000S-3”-31 | 压力测量接头 | 1 |
HNA 2250-TWS 压裂泵液力端配件清单
序号 | HNA 部件号 | 名称 | 数量 |
0 | HNA 2250TWS-4.5-0 | 液力端总成 | 1 |
1 | HNA 2250TWS-4.5-1 | 阀箱 | 1 |
2 | HNA 2250TWS-4.5-2 | 阀座O型圈 | 6 |
3 | HNA 2250TWS-4.5-3 | 阀座 | 6 |
4 | HNA 2250TWS-4.5-4 | 阀胶皮 | 6 |
5 | HNA 2250TWS-4.5-5 | 阀体 | 6 |
6 | HNA 2250TWS-4.5-6 | 弹簧 | 6 |
7 | HNA 2250TWS-4.5-7 | 排出压盖 | 2 |
8 | HNA 2250TWS-4.5-8 | 排出压帽 | 2 |
9 | HNA 2250TWS-4.5-9 | 排出压盖密封 | 3 |
10 | HNA 2250TWS-4.5-10 | 排出压盖密封挡圈 | 3 |
11 | HNA 2250TWS-4.5-11 | 压盖O型圈 | 3 |
12 | HNA 2250TWS-4.5-12 | 柱塞端垫圈 | 3 |
13 | HNA 2250TWS-4.5-13 | 弧型密封 | 3 |
14 | HNA 2250TWS-4.5-14 | V型密封 | 6 |
15 | HNA 2250TWS-4.5-15 | 柱塞铜套 | 3 |
16 | HNA 2250TWS-4.5-16 | 柱塞压帽油封 | 3 |
17 | HNA 2250TWS-4.5-17 | 柱塞压帽 | 3 |
18 | HNA 2250TWS-4.5-18 | 柱塞 | 3 |
19 | HNA 2250TWS-4.5-19 | 弹簧支架 | 3 |
20 | HNA 2250TWS-4.5-20 | 弹簧支架 | 3 |
21 | HNA 2250TWS-4.5-21 | 吸入压盖密封挡圈 | 3 |
22 | HNA 2250TWS-4.5-22 | 吸入压盖O型圈 | 6 |
23 | HNA 2250TWS-4.5-23 | 吸入压盖 | 3 |
24 | HNA 2250TWS-4.5-24 | 吸入压帽 | 3 |
25 | HNA 2250TWS-4.5-25 | 3”油壬密封 | 1 |
26 | HNA 2250TWS-4.5-26 | 排出法兰 | 1 |
27 | HNA 2250TWS-4.5-27 | 排出法兰螺母 | 12 |
28 | HNA 2250TWS-4.5-28 | 平垫圈 | 12 |
29 | HNA 2250TWS-4.5-29 | 双头螺栓 | 12 |
30 | HNA 2250TWS-4.5-30 | 法兰O型圈 | 2 |
31 | HNA 2250TWS-4.5-31 | 传感器接头 | 1 |
32 | HNA 2250TWS-4.5-32 | 传感器压筒 | 1 |
33 | HNA 2250TWS-4.5-33 | 盲法兰 | 1 |
HNA 2500-QWS 五缸压裂泵液力端配件清单
序号 | HNA 部件号 | 名称 | 数量 |
0 | HNA 2500QWS-4-0 | 液力端总成 | 1 |
1 | HNA 2500QWS-4-1 | 阀箱 | 1 |
2 | HNA 2500QWS-4-2 | 阀座O型圈 | 10 |
3 | HNA 2500QWS-4-3 | 阀座 | 10 |
4 | HNA 2500QWS-4-4 | 阀胶皮 | 10 |
5 | HNA 2500QWS-4-5 | 阀体 | 10 |
6 | HNA 2500QWS-4-6 | 弹簧 | 10 |
7 | HNA 2500QWS-4-7 | 排出压盖密封 | 4 |
8 | HNA 2500QWS-4-8 | 排出压盖密封挡圈 | 4 |
9 | HNA 2500QWS-4-9 | 排出压盖 | 4 |
10 | HNA 2500QWS-4-10 | 排出压帽 | 4 |
11 | HNA 2500QWS-4-11 | 吸入压盖密封 | 5 |
12 | HNA 2500QWS-4-12 | 吸入压盖 | 5 |
13 | HNA 2500QWS-4-13 | 吸入压帽 | 5 |
14 | HNA 2500QWS-4-14 | 弹簧支架 | 5 |
15 | HNA 2500QWS-4-15 | 柱塞 | 5 |
16 | HNA 2500QWS-4-16 | 柱塞端垫圈 | 5 |
17 | HNA 2500QWS-4-17 | 弧型密封 | 5 |
18 | HNA 2500QWS-4-18 | V型密封 | 10 |
19 | HNA 2500QWS-4-19 | 柱塞铜套 | 5 |
20 | HNA 2500QWS-4-20 | 柱塞压帽油封 | 5 |
21 | HNA 2500QWS-4-21 | 柱塞压帽 | 5 |
22 | HNA 2500QWS-4-22 | 卡箍 | 5 |
23 | HNA 2500QWS-4-23 | 卡箍螺钉 | 10 |
24 | HNA 2500QWS-4-24 | 传感器接头 | 1 |
25 | HNA YL-YRMF-2 | 2”油壬密封 | 1 |
26 | HNA 2500QWS-4-26 | 传感器压筒 | 1 |
27 | HNA 2500QWS-4-27 | 排出法兰 | 1 |
28 | HNA 2500QWS-4-28 | 排出法兰螺母 | 12 |
29 | HNA 2500QWS-4-29 | 平垫圈 | 12 |
30 | HNA 2500QWS-4-30 | 双头螺栓 | 12 |
31 | HNA 2500QWS-4-31 | 法兰O型圈 | 2 |
32 | HNA YL-YRMF-3 | 3”油壬密封 | 1 |
哈里伯顿HT-400 柱塞泵原厂部件号--HNA可供互换产品
哈里伯顿HT-400液力端总成
LOC |
Part Description |
QTY | Plunger Size/Part Number | ||||
3-3/8 In | 4 In | 4-1/2 In | 5 In | 6 In | |||
1 | FLANGE, DISCHARGE, BLANK | 1 | --- | 316.22980.KOP | 316.22980.KOP | 316.22980.KOP | 316.22980.KOP |
1a | FLANGE, DISCH, RH | 1 | 316.21676.KOP | 316.23019.KOP | 316.23019.KOP | 316.23019.KOP | 316.23019.KOP |
1b | FLANGE, DISCH, LH | 1 | 316.21677.KOP | 316.23017.KOP | 316.23017.KOP | 316.23017.KOP | 316.23017.KOP |
1c | FLANGE, STRAIGHT | 1 | 316.21013.KOP | 316.27482.KOP | 316.27482.KOP | 316.27482.KOP | 316.27482.KOP |
2 | SEAL, DISCHARGE PASSAGE | 6 | 315.27117.KOP | 316.2547.KOP | 316.2547.KOP | 316.2547.KOP | 316.2547.KOP |
3 | NUT, 1-14 NF, INTERNAL WRENCHING | 4 | 316.11621.KOP | 316.11621.KOP | 316.11621.KOP | 316.11621.KOP | 316.11621.KOP |
4 | STUD,FLUID END TO DISCH. FLANGE * | 4 | 316.23013.KOP | --- | 316.23013.KOP | 316.23013.KOP | 316.23013.KOP |
5 | BOLT, TOP, TIE | 1 | 316.27488.KOP | 316.27488.KOP | 316.27488.KOP | 316.27488.KOP | 316.27488.KOP |
6 | NUT, TOP TIE BOLT | 2 | 316.25501.KOP | 316.25501.KOP | 316.25501.KOP | 316.25501.KOP | 316.25501.KOP |
7 | WASHER, HARDENED | 2 | 315.11183.KOP | 315.11183.KOP | --- | --- | --- |
8 | SPACER, INN, DISCH PASS SEAL | 2 | 316.2145.KOP | 316.2545.KOP | 316.2545.KOP | 316.2545.KOP | 316.2545.KOP |
9 | FLUID END SECTION | 3 | 316.21951.KOP | 316.22982.KOP | 316.23951.KOP | 316.24951.KOP | 316.27951.KOP |
10 | NUT, ELASTIC * | 2 | 70.32760.KOP | --- | 70.32760.KOP | 70.32760.KOP | 70.32760.KOP |
11 | BOLT, BOTTOM, TIE * | 1 | 316.23011.KOP | --- | 316.23011.KOP | 316.23011.KOP | 316.23011.KOP |
** | BOLT, TIE, FLUID END, TOP | 2 | --- | 316.27489.KOP | --- | --- | --- |
** | STUD, FLUID END TO POWER END | 12 | 316.24923.KOP | 316.24923.KOP | 316.24923.KOP | 316.24923.KOP | 316.24923.KOP |
12 | O-RING, SUCTION MODULE MANIFOLD | 3 | Note: Suction manifold components (LOC12 - LOC15) are considered part of the unit that the pump is installed on rather than part of the fluid end assembly. These components are shown for information purposes only and can be provided by KOP based on the customer’s requirements. | ||||
13 | MANIFOLD, SUCTION | 1 | |||||
14 | WASHER, LOCK, SUCTION MANIFOLD | 12 | |||||
15 | BOLTS, SUCTION MANIFOLD | 12 | |||||
哈里伯顿HT-400排出阀总成
LOC |
Part Description |
QTY | Plunger Size/Part Number | ||||
3-3/8 In | 4 In | 4-1/2 In | 5 In | 6 In | |||
1 | RETAINER, COVER | 3 | 316.2102.KOP | 316.2202.KOP | 316.2202.KOP | 316.2502.KOP | 316.2502.KOP |
2 | COVER,DOUBLE GUIDE VALVE | 3 | 316.2109.KOP | 316.23091.KOP | 316.23091.KOP | 316.24044.KOP | 316.24044.KOP |
3 | GASKET, VALVE COVER | 3 | 316.21052.KOP | 316.22052.KOP | 316.22052.KOP | 316.25052.KOP | 316.25052.KOP |
4 | RING,SPACER, VALVE COVER | 3 | 316.21051.KOP | 316.22051.KOP | 316.22051.KOP | 316.25051.KOP | 316.25051.KOP |
5 | INSERT, 2 PC BUSHING, VALVE GUIDE | 6 | 316.22004.KOP | 316.22004.KOP | 316.22004.KOP | 316.22006.KOP | 316.22006.KOP |
6 | LINER, 2 PC BUSHING, VALVE GUIDE | 6 | 316.22005.KOP | 316.22005.KOP | 316.22005.KOP | 316.22007.KOP | 316.22007.KOP |
7 | SPRING, VALVE | 3 | 316.2108.KOP | 316.2108.KOP | 316.2308.KOP | 316.27259.KOP | 316.27259.KOP |
8 | VALVE, FRAC | 3 | 316.21007.KOP | 316.21007.KOP | 316.22048.KOP | 316.24027.KOP | 316.24027.KOP |
9 | INSERT, VALVE, STD, URETHANE | 3 | 316.21006.KOP | 316.21006.KOP | 316.22049.KOP | 316.24037.KOP | 316.24037.KOP |
9 | INSERT, VALVE, ACID, URETHANE | 3 | 316.21048.KOP | 316.21048.KOP | 316.22046.KOP | 316.24026.KOP | 316.24026.KOP |
10 | SEAT VALVE, TAPERED | 3 | 316.21008.KOP | 316.21008.KOP | 316.22047.KOP | 316.24024.KOP | 316.24024.KOP |
11 | O-RING | 3 | 8.34037.KOP | 8.34037.KOP | 8.34041.KOP | 8.34045.KOP | 8.34045.KOP |
12 | RETAINER, GUIDE BUSHING | 3 | 316.21096.KOP | 316.21096.KOP | 316.23953.KOP | 316.24043.KOP | 316.24043.KOP |
哈里伯顿HT-400柱塞/缸盖总成
LOC |
Part Description |
QTY | Plunger Size/Part Number | ||||
3-3/8 In | 4 In | 4-1/2 In | 5 In | 6 In | |||
1 | RETAINER, COVER | 3 | 316.2102.KOP | 316.2102.KOP | 316.2202.KOP | 316.2502.KOP | 316.2506.KOP |
2 | COVER,CYLINDER HEAD | 3 | 316.2107.KOP | 316.2107.KOP | 316.2207.KOP | 316.2407.KOP | 316.2507.KOP |
3 | GASKET, COVER | 3 | 316.21052.KOP | 316.21052.KOP | 316.22052.KOP | 316.25052.KOP | 316.25074.KOP |
4 | RING, SPACER, COVER | 3 | 316.21051.KOP | 316.21051.KOP | 316.22051.KOP | 316.25051.KOP | 316.25073.KOP |
5 | NOSE, PLUNGER | 3 | 316.2131.KOP | 316.2231.KOP | 316.2331.KOP | 316.2331.KOP | 316.2331.KOP |
6 | SEAL, PLUNGER NOSE ASSEMBLY | 3 | 316.2130.KOP | 316.2230.KOP | 316.2330.KOP | 316.2330.KOP | 316.2330.KOP |
7 | PLUNGER, HARD SURFACE | 3 | 316.21026.KOP | 316.22294.KOP | 316.23085.KOP | 316.24296.KOP | 316.25162.KOP |
8 | TIE ROD, PLUNGER | 3 | 316.21028.KOP | 316.21028.KOP | 316.21028.KOP | 316.25165.KOP | 316.25165.KOP |
9 | ADAPTER, PUSHROD | 3 | 316.21059.KOP | 316.22302.KOP | 316.23089.KOP | 316.24336.KOP | 316.25172.KOP |
哈里伯顿HT-400盘根盒总成
LOC |
Part Description |
QTY | Plunger Size/Part Number | ||||
3-3/8 In | 4 In | 4-1/2 In | 5 In | 6 In | |||
1 | PIN, GROOVE | 3 | 70.35817.KOP | 70.35817.KOP | 70.35817.KOP | 70.35785.KOP | 70.35785.KOP |
2 | SLEEVE, WIPER GLAND | 3 | 316.2138.KOP | 316.2238.KOP | 316.2238.KOP | 316.2438.KOP | 316.2738.KOP |
3 | NUT, PACKING ADJUSTMENT | 3 | 316.2137.KOP | 316.22987.KOP | 316.2337.KOP | 316.2437.KOP | 316.2737.KOP |
4 | CARRIER, SEAL & PACKING | 3 | 316.21391.KOP | 316.22396.KOP | 316.23391.KOP | 316.24391KOP | 316.27391.KOP |
5 | O-RING, 90D | 3 | 8.34040.KOP | 8.34045.KOP | 8.34049.KOP | 8.34053.KOP | 8.34058.KOP |
6 | RING, BACKUP, PACKING | 3 | 316.21393.KOP | 316.22393.KOP | 316.23393.KOP | 339.01527.KOP | 339.00036.KOP |
7 | PACKING SET, STD SRV, 3 RINGS | 1 | 316.21532.KOP | 316.22532.KOP | 316.23532.KOP | 316.24532.KOP | 316.27532.KOP |
7 | PACKING SET, ACID SRV, 3 RINGS | 1 | 316.21525.KOP | 316.22525.KOP | 316.23525.KOP | 316.24525.KOP | 316.27525.KOP |
8 | RING, HEADER | 3 | 316.21501.KOP | 316.22501.KOP | 316.23501.KOP | 316.24501.KOP | 316.27501.KOP |
9 | ADAPTER, HEADER RING | 3 | 316.21503.KOP | 316.22503.KOP | 316.23503.KOP | 316.24503.KOP | 316.27503.KOP |
10 | SEAL, LUBE, PACKING | 3 | 316.21395.KOP | 316.22395.KOP | 316.23395.KOP | 316.24395.KOP | 316.27395.KOP |
微信公众号
